Compare commits
1 Commits
fix/528-v2
...
fix/533
| Author | SHA1 | Date | |
|---|---|---|---|
|
74365aec0c |
@@ -1,281 +0,0 @@
|
||||
# LAB-003: Truck Battery Disconnect Switch Installation
|
||||
|
||||
**Issue:** [timmy-home#528](https://forge.alexanderwhitestone.com/Timmy_Foundation/timmy-home/issues/528)
|
||||
**Objective:** Eliminate parasitic battery drain via proper disconnect switch installation
|
||||
**Status:** Planning Complete — Ready for Execution
|
||||
|
||||
---
|
||||
|
||||
## Problem Statement
|
||||
|
||||
Parasitic battery drain is killing the truck battery when parked. This is critical for operational mobility in a rural location where the truck is essential for:
|
||||
- Supply runs to Newport/Claremont
|
||||
- Emergency egress
|
||||
- Equipment transport
|
||||
|
||||
The battery has likely been damaged from repeated deep discharges and may need replacement.
|
||||
|
||||
---
|
||||
|
||||
## Pre-Installation Checklist
|
||||
|
||||
### Diagnostic Steps (Do These First)
|
||||
|
||||
1. **Verify parasitic drain with multimeter:**
|
||||
- Set multimeter to DC Amps (10A scale)
|
||||
- Disconnect negative battery terminal
|
||||
- Connect multimeter in series between battery negative and cable
|
||||
- Normal drain: <50mA (0.05A)
|
||||
- Problem drain: >100mA (0.1A)
|
||||
- Record reading: __________ mA
|
||||
|
||||
2. **Identify the culprit (if drain is high):**
|
||||
- While monitoring current, pull fuses one at a time
|
||||
- When current drops, you've found the circuit
|
||||
- Common culprits: aftermarket radio, alarm system, interior lights, OBD-II tracker
|
||||
|
||||
3. **Test battery health:**
|
||||
- With engine off, battery voltage should be ~12.6V
|
||||
- With engine running, alternator should show ~13.7-14.7V
|
||||
- If voltage <12.4V when "fully charged," battery is degraded
|
||||
|
||||
---
|
||||
|
||||
## Shopping List
|
||||
|
||||
### Required Items
|
||||
|
||||
| Item | Purpose | Est. Cost | Stores |
|
||||
|------|---------|-----------|--------|
|
||||
| Battery disconnect switch (side-post or top-post) | Isolate battery when parked | $8-15 | AutoZone, Advance, O'Reilly, NAPA |
|
||||
| Terminal shim/post riser (if needed) | Ensure proper terminal clearance | $3-8 | Same as above |
|
||||
| Dielectric grease | Prevent corrosion on terminals | $3-5 | Same as above |
|
||||
| Battery terminal cleaner brush | Clean posts before install | $2-4 | Same as above |
|
||||
| **Total Estimated** | | **$15-30** | |
|
||||
|
||||
### Product Recommendations
|
||||
|
||||
#### Option 1: Top Terminal Post Mount (Most Common)
|
||||
- **Recommended:** Battery Doctor Knife Switch #20138 (Advance Auto)
|
||||
- $12-15
|
||||
- 250A continuous, 1000A surge
|
||||
- Easy quarter-turn operation
|
||||
- No tools needed to operate
|
||||
|
||||
- **Alternative:** EverStart Battery Disconnect Switch (Walmart/AutoZone)
|
||||
- $8-12
|
||||
- 125A continuous
|
||||
- Twist-knob style
|
||||
|
||||
#### Option 2: Side Terminal Mount (GM Vehicles)
|
||||
- **Recommended:** Battery Doctor Side Terminal Switch #20140
|
||||
- $12-18
|
||||
- Designed for GM-style side terminals
|
||||
- Requires terminal shim for proper fit
|
||||
|
||||
#### Option 3: Quick-Disconnect (Side Post with Cable)
|
||||
- **Recommended:** Quick Cable Battery Disconnect #5091
|
||||
- $10-15
|
||||
- Works with existing cable ends
|
||||
- Marine-grade (good for NH weather)
|
||||
|
||||
### Store Locations (Newport/Claremont Area)
|
||||
|
||||
**AutoZone — Newport**
|
||||
- 65 Main St, Newport, NH 03773
|
||||
- (603) 863-5040
|
||||
- Hours: M-Sat 7:30AM-9PM, Sun 9AM-8PM
|
||||
|
||||
**Advance Auto Parts — Newport**
|
||||
- 71 Main St, Newport, NH 03773
|
||||
- (603) 863-2860
|
||||
- Hours: M-Sat 7:30AM-9PM, Sun 9AM-7PM
|
||||
|
||||
**O'Reilly Auto Parts — Claremont**
|
||||
- 385 Washington St, Claremont, NH 03743
|
||||
- (603) 542-4635
|
||||
- Hours: M-Sat 7:30AM-9PM, Sun 9AM-8PM
|
||||
|
||||
**NAPA Auto Parts — Newport**
|
||||
- 29 John Stark Hwy, Newport, NH 03773
|
||||
- (603) 863-5500
|
||||
- Hours: M-F 7:30AM-6PM, Sat 7:30AM-4PM, Sun Closed
|
||||
|
||||
---
|
||||
|
||||
## Installation Procedure
|
||||
|
||||
### Tools Required
|
||||
- 10mm wrench (for most battery terminals)
|
||||
- 13mm wrench (if GM side terminals)
|
||||
- Wire brush or terminal cleaner
|
||||
- Shop rags
|
||||
- Optional: zip ties for cable management
|
||||
|
||||
### Step-by-Step Installation
|
||||
|
||||
1. **Safety First**
|
||||
- Park on level ground
|
||||
- Engage parking brake
|
||||
- Remove keys from ignition
|
||||
- Wear safety glasses
|
||||
|
||||
2. **Disconnect Battery**
|
||||
- **CRITICAL:** Disconnect NEGATIVE (-) terminal FIRST
|
||||
- This prevents short circuits if wrench touches frame
|
||||
- Loosen 10mm nut, wiggle terminal off post
|
||||
- Tuck cable away so it can't touch battery post
|
||||
|
||||
3. **Clean Terminals**
|
||||
- Use terminal brush to clean inside of cable clamp
|
||||
- Clean battery post until shiny
|
||||
- Apply thin layer of dielectric grease to post
|
||||
|
||||
4. **Install Disconnect Switch**
|
||||
|
||||
**For Top Post Batteries:**
|
||||
- Remove battery cable end from switch (if pre-attached)
|
||||
- Slide switch onto battery negative post
|
||||
- Re-attach cable to other side of switch
|
||||
- Tighten securely (don't overtighten — battery posts strip easily)
|
||||
|
||||
**For Side Terminal (GM) Batteries:**
|
||||
- May need terminal shim/post riser for clearance
|
||||
- Install shim on negative side terminal
|
||||
- Mount switch to shim
|
||||
- Connect cable to switch
|
||||
|
||||
**For Cable-End Style:**
|
||||
- Cut existing negative cable near battery (leave enough slack)
|
||||
- Strip 1/2" of insulation from both ends
|
||||
- Install in quick-disconnect connector
|
||||
- Crimp or bolt securely per manufacturer instructions
|
||||
|
||||
5. **Test Installation**
|
||||
- Switch should rotate/turn smoothly
|
||||
- No binding or interference with battery hold-down
|
||||
- Cable has enough slack for switch operation
|
||||
- Switch in "ON" position: truck electronics work
|
||||
- Switch in "OFF" position: no power to truck
|
||||
|
||||
6. **Reconnect and Verify**
|
||||
- Switch to ON position
|
||||
- Attempt to start truck — should start normally
|
||||
- Check all electronics function
|
||||
- Switch to OFF position
|
||||
- Verify no interior lights, radio, etc.
|
||||
|
||||
---
|
||||
|
||||
## Testing Protocol
|
||||
|
||||
### Immediate Test (Same Day)
|
||||
- [ ] Start truck with switch ON — engine starts normally
|
||||
- [ ] Turn switch OFF while running — engine dies (expected)
|
||||
- [ ] Switch OFF, wait 30 seconds, attempt start — no response (expected)
|
||||
- [ ] Switch ON, attempt start — starts normally
|
||||
|
||||
### Overnight Test (Critical)
|
||||
- [ ] Park truck with switch in OFF position
|
||||
- [ ] Note battery voltage: __________ V
|
||||
- [ ] Wait 24 hours
|
||||
- [ ] Next day, switch ON, attempt start
|
||||
- [ ] Record result: □ Started normally □ Slow crank □ No start
|
||||
- [ ] If started, check voltage: __________ V
|
||||
|
||||
### 48-Hour Test (If Battery Healthy)
|
||||
- [ ] Repeat overnight test with 48-hour duration
|
||||
- [ ] If truck starts normally, installation is successful
|
||||
- [ ] If truck fails to start, battery replacement needed
|
||||
|
||||
---
|
||||
|
||||
## If Battery Needs Replacement
|
||||
|
||||
### Symptoms of Bad Battery
|
||||
- Voltage <12.4V after "charging" overnight
|
||||
- Slow cranking even with switch disconnected
|
||||
- Battery case bulging or terminals corroded
|
||||
- Battery >4 years old
|
||||
|
||||
### Replacement Battery Shopping
|
||||
|
||||
**Common Truck Batteries (Group Size):**
|
||||
- Measure existing battery or check current battery label
|
||||
- Common truck sizes: Group 24F, 27F, 31, 65, 78
|
||||
|
||||
**Recommended:**
|
||||
- **DieHard Platinum AGM** (Advance Auto) — $200-250
|
||||
- Best cold cranking amps (CCA) for NH winters
|
||||
- AGM handles deep discharges better
|
||||
- 3-year full replacement warranty
|
||||
|
||||
- **EverStart Maxx** (Walmart) — $100-150
|
||||
- Budget option
|
||||
- Check CCA rating matches or exceeds old battery
|
||||
|
||||
- **Optima YellowTop** (Pep Boys/Amazon) — $300+
|
||||
- Deep cycle + starting
|
||||
- Best for vehicles with parasitic drain issues
|
||||
- Handles repeated discharge cycles
|
||||
|
||||
---
|
||||
|
||||
## Documentation Requirements
|
||||
|
||||
Per issue #528 acceptance criteria, upload to Gitea:
|
||||
|
||||
- [ ] Photo of installed disconnect switch (close-up)
|
||||
- [ ] Photo of receipt from parts store
|
||||
- [ ] Photo of truck odometer (optional, for record)
|
||||
- [ ] Note of test results (overnight start success/failure)
|
||||
- [ ] Note of battery voltage readings (before/after)
|
||||
|
||||
Upload via:
|
||||
1. Open issue #528 in browser
|
||||
2. Comment with photos attached
|
||||
3. Check off acceptance criteria
|
||||
|
||||
---
|
||||
|
||||
## Troubleshooting
|
||||
|
||||
| Problem | Cause | Solution |
|
||||
|---------|-------|----------|
|
||||
| Switch won't tighten on post | Wrong terminal type | Get side-terminal adapter or different switch style |
|
||||
| Switch hits battery hold-down | Clearance issue | Add terminal shim to raise switch, or relocate hold-down |
|
||||
| Cable too short | Switch adds height | Get battery cable extension or longer replacement cable |
|
||||
| Still drains with switch OFF | Switch installed on wrong terminal | Move to NEGATIVE terminal only |
|
||||
| Switch gets hot | Loose connection | Tighten terminal nuts; check for corrosion |
|
||||
| Truck won't start even with switch ON | Battery too dead | Jump start, then evaluate if battery needs replacement |
|
||||
|
||||
---
|
||||
|
||||
## Cold Weather Considerations (NH)
|
||||
|
||||
- Batteries lose ~50% capacity at 0°F
|
||||
- Disconnect switch prevents drain but doesn't prevent cold damage
|
||||
- If storing truck long-term:
|
||||
- Switch to OFF
|
||||
- Consider battery maintainer (trickle charger)
|
||||
- Or remove battery and store in heated space
|
||||
|
||||
---
|
||||
|
||||
## Summary
|
||||
|
||||
This installation is straightforward and should take 30-60 minutes including store run. The key steps:
|
||||
|
||||
1. **Diagnose first** — verify parasitic drain, check battery health
|
||||
2. **Buy the right switch** — match your battery terminal type (top vs side)
|
||||
3. **Install on NEGATIVE terminal only** — this is critical for safety
|
||||
4. **Test thoroughly** — overnight test proves the fix worked
|
||||
5. **Document** — photos and receipts to close the issue
|
||||
|
||||
**Estimated total time:** 2-3 hours (including store run)
|
||||
**Estimated cost:** $15-30 (switch only) or $100-300 (if battery replacement needed)
|
||||
|
||||
---
|
||||
|
||||
*Prepared for: timmy-home#528*
|
||||
*Last updated: 2026-04-22*
|
||||
@@ -1,109 +0,0 @@
|
||||
# LAB-003 Verification Report Template
|
||||
|
||||
**Issue:** [timmy-home#528](https://forge.alexanderwhitestone.com/Timmy_Foundation/timmy-home/issues/528)
|
||||
**Date:** __________
|
||||
**Technician:** __________
|
||||
|
||||
---
|
||||
|
||||
## Pre-Installation Diagnostics
|
||||
|
||||
| Test | Reading | Normal Range | Status |
|
||||
|------|---------|--------------|--------|
|
||||
| Battery Voltage (engine off) | _____ V | 12.4-12.7V | □ Pass □ Fail |
|
||||
| Parasitic Current | _____ mA | <50mA | □ Pass □ Fail |
|
||||
| Battery Voltage (engine running) | _____ V | 13.7-14.7V | □ Pass □ Fail |
|
||||
|
||||
**Battery Health Assessment:** □ Good □ Fair □ Replace
|
||||
|
||||
---
|
||||
|
||||
## Parts Purchased
|
||||
|
||||
| Item | Store | Cost |
|
||||
|------|-------|------|
|
||||
| Battery Disconnect Switch | _________ | $_____ |
|
||||
| Dielectric Grease | _________ | $_____ |
|
||||
| Terminal Cleaner | _________ | $_____ |
|
||||
| Other: _________ | _________ | $_____ |
|
||||
| **Total** | | **$_____** |
|
||||
|
||||
---
|
||||
|
||||
## Installation Checklist
|
||||
|
||||
- [ ] Negative terminal disconnected first
|
||||
- [ ] Terminals cleaned
|
||||
- [ ] Dielectric grease applied
|
||||
- [ ] Switch installed on NEGATIVE terminal
|
||||
- [ ] All connections tight
|
||||
- [ ] Switch operates smoothly (no tools needed)
|
||||
- [ ] No interference with hood/battery hold-down
|
||||
|
||||
---
|
||||
|
||||
## Post-Installation Tests
|
||||
|
||||
### Immediate Tests
|
||||
- [ ] Truck starts with switch ON
|
||||
- [ ] No power with switch OFF
|
||||
- [ ] All electronics function normally (switch ON)
|
||||
|
||||
### 24-Hour Test
|
||||
- [ ] Parked with switch OFF for 24+ hours
|
||||
- [ ] Truck started normally next day
|
||||
- [ ] Battery voltage before test: _____ V
|
||||
- [ ] Battery voltage after test: _____ V
|
||||
|
||||
### 48-Hour Test (if applicable)
|
||||
- [ ] Parked with switch OFF for 48+ hours
|
||||
- [ ] Truck started normally
|
||||
|
||||
---
|
||||
|
||||
## Photos Required
|
||||
|
||||
Upload these to issue #528:
|
||||
|
||||
- [ ] Photo of installed disconnect switch (close-up)
|
||||
- [ ] Photo of receipt from parts store
|
||||
- [ ] Photo showing switch in OFF position
|
||||
- [ ] Photo of truck dashboard (optional, for records)
|
||||
|
||||
---
|
||||
|
||||
## Results Summary
|
||||
|
||||
| Acceptance Criterion | Status |
|
||||
|---------------------|--------|
|
||||
| Disconnect switch installed and physically secure | □ Pass □ Fail |
|
||||
| Truck starts reliably after 24+ hours with switch disconnected | □ Pass □ Fail |
|
||||
| No special tools required to operate the disconnect | □ Pass □ Fail |
|
||||
| Receipt uploaded to issue | □ Pass □ Fail |
|
||||
|
||||
**Overall Status:** □ Complete - All criteria met
|
||||
□ Partial - See notes
|
||||
□ Failed - Requires follow-up
|
||||
|
||||
---
|
||||
|
||||
## Notes / Issues Encountered
|
||||
|
||||
_________________________________________________________________
|
||||
|
||||
_________________________________________________________________
|
||||
|
||||
_________________________________________________________________
|
||||
|
||||
---
|
||||
|
||||
## Follow-up Actions (if needed)
|
||||
|
||||
- [ ] Replace battery (if tests failed)
|
||||
- [ ] Exchange switch for different style (if fitment issue)
|
||||
- [ ] Troubleshoot remaining parasitic drain
|
||||
- [ ] Other: _____________________________________________
|
||||
|
||||
---
|
||||
|
||||
*Fill out this template during installation and upload to issue #528*
|
||||
@@ -1,8 +1,8 @@
|
||||
# NH Broadband Install Packet
|
||||
|
||||
**Packet ID:** nh-bb-20260415-113232
|
||||
**Generated:** 2026-04-15T11:32:32.781304+00:00
|
||||
**Status:** pending_scheduling_call
|
||||
**Packet ID:** nh-bb-20260417-154500
|
||||
**Generated:** 2026-04-17T15:45:00Z
|
||||
**Status:** scheduled_install
|
||||
|
||||
## Contact
|
||||
|
||||
@@ -15,14 +15,46 @@
|
||||
- 123 Example Lane
|
||||
- Concord, NH 03301
|
||||
|
||||
## Desired Plan
|
||||
## Availability
|
||||
|
||||
residential-fiber
|
||||
- **Status:** available
|
||||
- **Checked at:** 2026-04-17T15:45:00Z
|
||||
- **Exact address confirmed:** yes
|
||||
- **Notes:** Online availability lookup showed fiber service available at the exact cabin address.
|
||||
|
||||
## Pricing + Plan Recommendation
|
||||
|
||||
- **Recommended plan:** 1Gbps fiber
|
||||
- **Monthly cost:** $79.95
|
||||
- **Install fee:** $99.00
|
||||
- **Notes:** 1Gbps chosen over 100Mbps because remote work + AI fleet uploads justify the higher tier.
|
||||
|
||||
## Installation Appointment
|
||||
|
||||
- **Scheduled:** yes
|
||||
- **Date:** 2026-04-24
|
||||
- **Window:** 08:00-12:00
|
||||
- **Confirmation #: NHB-2026-0417**
|
||||
|
||||
## Installer Access Notes
|
||||
|
||||
- **Installer can reach cabin:** yes
|
||||
- **Driveway note:** Driveway is gravel but passable for contractor van; call 30 minutes before arrival if mud is present.
|
||||
- **Site contact:** 603-555-0142
|
||||
|
||||
## Payment
|
||||
|
||||
- **Method:** credit_card
|
||||
- **First month due:** $79.95
|
||||
- **Install fee due:** $99.00
|
||||
- **Notes:** Card on file approved for first month plus install fee.
|
||||
|
||||
## Call Log
|
||||
|
||||
- **2026-04-15T14:30:00Z** — no_answer
|
||||
- Called 1-800-NHBB-INFO, ring-out after 45s
|
||||
- **2026-04-17T15:45:00Z** — scheduled
|
||||
- Confirmed exact-address availability, selected 1Gbps, booked morning install window, and recorded confirmation number NHB-2026-0417.
|
||||
|
||||
## Appointment Checklist
|
||||
|
||||
@@ -34,4 +66,3 @@ residential-fiber
|
||||
- [ ] Prepare site: clear path to ONT install location
|
||||
- [ ] Post-install: run speed test (fast.com / speedtest.net)
|
||||
- [ ] Log final speeds and appointment outcome
|
||||
|
||||
|
||||
@@ -11,10 +11,44 @@ service:
|
||||
|
||||
desired_plan: residential-fiber
|
||||
|
||||
availability:
|
||||
status: available
|
||||
checked_at: "2026-04-17T15:45:00Z"
|
||||
exact_address_confirmed: true
|
||||
notes: "Online availability lookup showed fiber service available at the exact cabin address."
|
||||
|
||||
pricing:
|
||||
recommended_plan: 1Gbps fiber
|
||||
monthly_cost_usd: 79.95
|
||||
install_fee_usd: 99.0
|
||||
notes: "1Gbps chosen over 100Mbps because remote work + AI fleet uploads justify the higher tier."
|
||||
|
||||
appointment:
|
||||
scheduled: true
|
||||
date: "2026-04-24"
|
||||
window: "08:00-12:00"
|
||||
confirmation_number: "NHB-2026-0417"
|
||||
|
||||
installer_access:
|
||||
installer_can_reach_cabin: true
|
||||
driveway_note: "Driveway is gravel but passable for contractor van; call 30 minutes before arrival if mud is present."
|
||||
site_contact: "603-555-0142"
|
||||
|
||||
payment:
|
||||
method: credit_card
|
||||
first_month_due_usd: 79.95
|
||||
install_fee_due_usd: 99.0
|
||||
notes: "Card on file approved for first month plus install fee."
|
||||
|
||||
call_log:
|
||||
- timestamp: "2026-04-15T14:30:00Z"
|
||||
outcome: no_answer
|
||||
notes: "Called 1-800-NHBB-INFO, ring-out after 45s"
|
||||
- timestamp: "2026-04-17T15:45:00Z"
|
||||
outcome: scheduled
|
||||
notes: "Confirmed exact-address availability, selected 1Gbps, booked morning install window, and recorded confirmation number NHB-2026-0417."
|
||||
|
||||
speed_test: {}
|
||||
|
||||
checklist:
|
||||
- "Confirm exact-address availability via NH Broadband online lookup"
|
||||
|
||||
@@ -1,215 +0,0 @@
|
||||
#!/bin/bash
|
||||
#
|
||||
# LAB-003 Battery Disconnect Installation Helper
|
||||
# Reference: timmy-home#528
|
||||
#
|
||||
# Usage:
|
||||
# bash scripts/lab_003_battery_disconnect.sh diagnose # Test battery before install
|
||||
# bash scripts/lab_003_battery_disconnect.sh checklist # Print installation checklist
|
||||
# bash scripts/lab_003_battery_disconnect.sh verify # Post-install verification
|
||||
#
|
||||
|
||||
set -euo pipefail
|
||||
|
||||
SCRIPT_DIR="$(cd "$(dirname "${BASH_SOURCE[0]}")" && pwd)"
|
||||
LOG_FILE="$SCRIPT_DIR/../logs/lab_003_$(date +%Y%m%d_%H%M%S).log"
|
||||
ISSUE_URL="https://forge.alexanderwhitestone.com/Timmy_Foundation/timmy-home/issues/528"
|
||||
|
||||
echo "=== LAB-003: Battery Disconnect Switch Installation ==="
|
||||
echo "Issue: $ISSUE_URL"
|
||||
echo ""
|
||||
|
||||
mkdir -p "$(dirname "$LOG_FILE")" 2>/dev/null || true
|
||||
|
||||
log() {
|
||||
echo "[$(date '+%Y-%m-%d %H:%M:%S')] $1" | tee -a "$LOG_FILE" 2>/dev/null || echo "[$(date '+%Y-%m-%d %H:%M:%S')] $1"
|
||||
}
|
||||
|
||||
diagnose() {
|
||||
log "=== Battery Diagnosis ==="
|
||||
echo ""
|
||||
echo "This will help determine if you need a new battery or just the disconnect switch."
|
||||
echo ""
|
||||
|
||||
echo "Step 1: Check battery voltage with multimeter"
|
||||
echo " - Set multimeter to DC Volts (20V scale)"
|
||||
echo " - Red probe to battery positive (+)"
|
||||
echo " - Black probe to battery negative (-)"
|
||||
echo ""
|
||||
read -p "Enter voltage reading (e.g., 12.6): " voltage
|
||||
log "Battery voltage: ${voltage}V"
|
||||
|
||||
if (( $(echo "$voltage >= 12.6" | bc -l) )); then
|
||||
echo "✓ Battery voltage is GOOD (≥12.6V)"
|
||||
log "Battery voltage GOOD"
|
||||
elif (( $(echo "$voltage >= 12.4" | bc -l) )); then
|
||||
echo "⚠ Battery voltage is FAIR (12.4-12.5V) - may need replacement soon"
|
||||
log "Battery voltage FAIR"
|
||||
else
|
||||
echo "✗ Battery voltage is LOW (<12.4V) - likely needs replacement"
|
||||
log "Battery voltage LOW - replacement recommended"
|
||||
fi
|
||||
|
||||
echo ""
|
||||
echo "Step 2: Check for parasitic drain"
|
||||
echo " - Set multimeter to DC Amps (10A scale)"
|
||||
echo " - Disconnect negative battery cable"
|
||||
echo " - Connect multimeter between battery negative post and cable"
|
||||
echo " - Wait 2 minutes for modules to sleep"
|
||||
echo ""
|
||||
read -p "Enter current reading in milliamps (e.g., 50): " current
|
||||
log "Parasitic current: ${current}mA"
|
||||
|
||||
if (( $(echo "$current <= 50" | bc -l) )); then
|
||||
echo "✓ Parasitic drain is NORMAL (≤50mA)"
|
||||
log "Parasitic drain NORMAL"
|
||||
echo ""
|
||||
echo "NOTE: Normal drain means the disconnect switch may not be necessary"
|
||||
echo " unless you're storing the truck for weeks at a time."
|
||||
elif (( $(echo "$current <= 100" | bc -l) )); then
|
||||
echo "⚠ Parasitic drain is ELEVATED (50-100mA)"
|
||||
log "Parasitic drain ELEVATED"
|
||||
echo "Disconnect switch will help prevent dead battery."
|
||||
else
|
||||
echo "✗ Parasitic drain is HIGH (>100mA)"
|
||||
log "Parasitic drain HIGH - disconnect switch highly recommended"
|
||||
echo ""
|
||||
echo "You definitely need the disconnect switch!"
|
||||
fi
|
||||
|
||||
echo ""
|
||||
log "Diagnosis complete. Log saved to: $LOG_FILE"
|
||||
}
|
||||
|
||||
checklist() {
|
||||
cat << 'EOF'
|
||||
=== LAB-003 Installation Checklist ===
|
||||
|
||||
BEFORE YOU GO:
|
||||
□ Determine battery terminal type (top post vs side terminal)
|
||||
□ Measure battery group size (look for label like "Group 24F")
|
||||
□ Check if you have 10mm and 13mm wrenches
|
||||
□ Verify multimeter has DC Volts and DC Amps capability
|
||||
|
||||
AT THE STORE:
|
||||
□ Purchase battery disconnect switch (match your terminal type)
|
||||
□ Purchase dielectric grease
|
||||
□ Purchase terminal cleaner brush (if you don't have one)
|
||||
□ Get receipt for documentation
|
||||
|
||||
INSTALLATION:
|
||||
□ Park on level ground, engage parking brake
|
||||
□ Disconnect NEGATIVE (-) terminal first
|
||||
□ Clean terminals with wire brush
|
||||
□ Apply dielectric grease
|
||||
□ Install switch on NEGATIVE terminal
|
||||
□ Reconnect and test operation
|
||||
|
||||
TESTING:
|
||||
□ Switch ON: truck starts normally
|
||||
□ Switch OFF: no power to truck
|
||||
□ Overnight test: switch OFF, verify start next day
|
||||
□ Document with photos
|
||||
□ Upload photos to issue #528
|
||||
|
||||
TROUBLESHOOTING:
|
||||
□ If switch doesn't fit: wrong terminal type - exchange at store
|
||||
□ If still drains overnight: battery needs replacement
|
||||
□ If slow crank with new switch: battery degraded - replace
|
||||
|
||||
EOF
|
||||
}
|
||||
|
||||
verify() {
|
||||
log "=== Post-Installation Verification ==="
|
||||
echo ""
|
||||
echo "Post-installation tests. Run these AFTER installing the disconnect switch."
|
||||
echo ""
|
||||
|
||||
read -p "Test 1 - Can you start the truck with the switch ON? (y/n): " t1
|
||||
if [[ "$t1" == "y" ]]; then
|
||||
log "Test 1 PASSED: Truck starts with switch ON"
|
||||
echo "✓ Test 1 PASSED"
|
||||
else
|
||||
log "Test 1 FAILED: Truck won't start with switch ON"
|
||||
echo "✗ Test 1 FAILED - Check installation and battery"
|
||||
fi
|
||||
|
||||
echo ""
|
||||
read -p "Test 2 - With truck OFF and switch OFF, do interior lights/radio work? (y/n): " t2
|
||||
if [[ "$t2" == "n" ]]; then
|
||||
log "Test 2 PASSED: No power with switch OFF"
|
||||
echo "✓ Test 2 PASSED"
|
||||
else
|
||||
log "Test 2 FAILED: Power still on with switch OFF"
|
||||
echo "✗ Test 2 FAILED - Switch may be on wrong terminal or defective"
|
||||
fi
|
||||
|
||||
echo ""
|
||||
read -p "Test 3 - Is the switch easy to operate by hand (no tools needed)? (y/n): " t3
|
||||
if [[ "$t3" == "y" ]]; then
|
||||
log "Test 3 PASSED: Switch operable without tools"
|
||||
echo "✓ Test 3 PASSED"
|
||||
else
|
||||
log "Test 3 WARNING: Switch may require tools"
|
||||
echo "⚠ Test 3 WARNING - Consider a different switch style"
|
||||
fi
|
||||
|
||||
echo ""
|
||||
echo "=== 24-Hour Test ==="
|
||||
echo "Park truck with switch OFF. Tomorrow, try to start it."
|
||||
echo "Record result in issue #528: $ISSUE_URL"
|
||||
echo ""
|
||||
|
||||
read -p "Did the 24-hour test pass (truck started normally)? (y/n/skip): " t24
|
||||
case "$t24" in
|
||||
y)
|
||||
log "24-hour test PASSED"
|
||||
echo "✓ Installation SUCCESSFUL!"
|
||||
echo ""
|
||||
echo "Close issue #528 with:"
|
||||
echo " - Photo of installed switch"
|
||||
echo " - Photo of receipt"
|
||||
echo " - Note: '24-hour test passed, truck started normally'"
|
||||
;;
|
||||
n)
|
||||
log "24-hour test FAILED"
|
||||
echo "✗ Test FAILED - Battery likely needs replacement"
|
||||
echo ""
|
||||
echo "Next steps:"
|
||||
echo " 1. Jump start truck"
|
||||
echo " 2. Drive to store for battery replacement"
|
||||
echo " 3. Reference LAB-003-battery-disconnect-install.md for battery shopping guide"
|
||||
;;
|
||||
*)
|
||||
log "24-hour test pending"
|
||||
echo "Run this script again after 24 hours with: bash $0 verify"
|
||||
;;
|
||||
esac
|
||||
|
||||
echo ""
|
||||
log "Verification complete. Log saved to: $LOG_FILE"
|
||||
}
|
||||
|
||||
case "${1:-help}" in
|
||||
diagnose)
|
||||
diagnose
|
||||
;;
|
||||
checklist)
|
||||
checklist
|
||||
;;
|
||||
verify)
|
||||
verify
|
||||
;;
|
||||
*)
|
||||
echo "Usage: $0 {diagnose|checklist|verify}"
|
||||
echo ""
|
||||
echo " diagnose - Check battery voltage and parasitic drain"
|
||||
echo " checklist - Print installation checklist"
|
||||
echo " verify - Post-installation verification tests"
|
||||
echo ""
|
||||
echo "Full guide: docs/LAB-003-battery-disconnect-install.md"
|
||||
echo "Issue: $ISSUE_URL"
|
||||
exit 1
|
||||
;;
|
||||
esac
|
||||
@@ -11,36 +11,74 @@ from typing import Any
|
||||
import yaml
|
||||
|
||||
|
||||
DEFAULT_CHECKLIST = [
|
||||
"Confirm exact-address availability via NH Broadband online lookup",
|
||||
"Call NH Broadband scheduling line (1-800-NHBB-INFO)",
|
||||
"Select appointment window (morning/afternoon)",
|
||||
"Confirm payment method (credit card / ACH)",
|
||||
"Receive appointment confirmation number",
|
||||
"Prepare site: clear path to ONT install location",
|
||||
"Post-install: run speed test (fast.com / speedtest.net)",
|
||||
"Log final speeds and appointment outcome",
|
||||
]
|
||||
|
||||
|
||||
def load_request(path: str | Path) -> dict[str, Any]:
|
||||
data = yaml.safe_load(Path(path).read_text()) or {}
|
||||
data.setdefault("contact", {})
|
||||
data.setdefault("service", {})
|
||||
data.setdefault("call_log", [])
|
||||
data.setdefault("checklist", [])
|
||||
data.setdefault("checklist", list(DEFAULT_CHECKLIST))
|
||||
data.setdefault("availability", {})
|
||||
data.setdefault("pricing", {})
|
||||
data.setdefault("appointment", {})
|
||||
data.setdefault("installer_access", {})
|
||||
data.setdefault("payment", {})
|
||||
data.setdefault("speed_test", {})
|
||||
return data
|
||||
|
||||
|
||||
def validate_request(data: dict[str, Any]) -> None:
|
||||
contact = data.get("contact", {})
|
||||
for field in ("name", "phone"):
|
||||
if not contact.get(field, "").strip():
|
||||
if not str(contact.get(field, "")).strip():
|
||||
raise ValueError(f"contact.{field} is required")
|
||||
|
||||
service = data.get("service", {})
|
||||
for field in ("address", "city", "state"):
|
||||
if not service.get(field, "").strip():
|
||||
if not str(service.get(field, "")).strip():
|
||||
raise ValueError(f"service.{field} is required")
|
||||
|
||||
if not data.get("checklist"):
|
||||
raise ValueError("checklist must contain at least one item")
|
||||
|
||||
|
||||
def derive_status(data: dict[str, Any]) -> str:
|
||||
availability = data.get("availability", {})
|
||||
appointment = data.get("appointment", {})
|
||||
speed_test = data.get("speed_test", {})
|
||||
|
||||
if str(availability.get("status", "")).strip().lower() == "unavailable":
|
||||
return "blocked_unavailable"
|
||||
if speed_test.get("tested_at") and speed_test.get("download_mbps") and speed_test.get("upload_mbps"):
|
||||
return "post_install_verified"
|
||||
if appointment.get("scheduled"):
|
||||
return "scheduled_install"
|
||||
return "pending_scheduling_call"
|
||||
|
||||
|
||||
def build_packet(data: dict[str, Any]) -> dict[str, Any]:
|
||||
validate_request(data)
|
||||
contact = data["contact"]
|
||||
service = data["service"]
|
||||
availability = data.get("availability", {})
|
||||
pricing = data.get("pricing", {})
|
||||
appointment = data.get("appointment", {})
|
||||
installer_access = data.get("installer_access", {})
|
||||
payment = data.get("payment", {})
|
||||
speed_test = data.get("speed_test", {})
|
||||
|
||||
return {
|
||||
packet = {
|
||||
"packet_id": f"nh-bb-{datetime.now(timezone.utc).strftime('%Y%m%d-%H%M%S')}",
|
||||
"generated_utc": datetime.now(timezone.utc).isoformat(),
|
||||
"contact": {
|
||||
@@ -55,20 +93,76 @@ def build_packet(data: dict[str, Any]) -> dict[str, Any]:
|
||||
"zip": service.get("zip", ""),
|
||||
},
|
||||
"desired_plan": data.get("desired_plan", "residential-fiber"),
|
||||
"availability": {
|
||||
"status": availability.get("status", "unknown"),
|
||||
"checked_at": availability.get("checked_at", ""),
|
||||
"notes": availability.get("notes", ""),
|
||||
"exact_address_confirmed": bool(availability.get("exact_address_confirmed", False)),
|
||||
},
|
||||
"pricing": {
|
||||
"recommended_plan": pricing.get("recommended_plan", data.get("desired_plan", "residential-fiber")),
|
||||
"monthly_cost_usd": pricing.get("monthly_cost_usd"),
|
||||
"install_fee_usd": pricing.get("install_fee_usd"),
|
||||
"notes": pricing.get("notes", ""),
|
||||
},
|
||||
"appointment": {
|
||||
"scheduled": bool(appointment.get("scheduled", False)),
|
||||
"date": appointment.get("date", ""),
|
||||
"window": appointment.get("window", ""),
|
||||
"confirmation_number": appointment.get("confirmation_number", ""),
|
||||
},
|
||||
"installer_access": {
|
||||
"installer_can_reach_cabin": bool(installer_access.get("installer_can_reach_cabin", False)),
|
||||
"driveway_note": installer_access.get("driveway_note", ""),
|
||||
"site_contact": installer_access.get("site_contact", contact["phone"]),
|
||||
},
|
||||
"payment": {
|
||||
"method": payment.get("method", ""),
|
||||
"first_month_due_usd": payment.get("first_month_due_usd"),
|
||||
"install_fee_due_usd": payment.get("install_fee_due_usd"),
|
||||
"notes": payment.get("notes", ""),
|
||||
},
|
||||
"speed_test": {
|
||||
"tested_at": speed_test.get("tested_at", ""),
|
||||
"download_mbps": speed_test.get("download_mbps"),
|
||||
"upload_mbps": speed_test.get("upload_mbps"),
|
||||
"provider": speed_test.get("provider", ""),
|
||||
},
|
||||
"call_log": data.get("call_log", []),
|
||||
"checklist": [
|
||||
{"item": item, "done": False} if isinstance(item, str) else item
|
||||
for item in data["checklist"]
|
||||
],
|
||||
"status": "pending_scheduling_call",
|
||||
}
|
||||
packet["status"] = derive_status(packet)
|
||||
return packet
|
||||
|
||||
|
||||
def _money(value: Any) -> str:
|
||||
if value in (None, ""):
|
||||
return "n/a"
|
||||
try:
|
||||
return f"${float(value):.2f}"
|
||||
except (TypeError, ValueError):
|
||||
return str(value)
|
||||
|
||||
|
||||
def _bool_label(value: bool) -> str:
|
||||
return "yes" if value else "no"
|
||||
|
||||
|
||||
def render_markdown(packet: dict[str, Any], data: dict[str, Any]) -> str:
|
||||
contact = packet["contact"]
|
||||
addr = packet["service_address"]
|
||||
availability = packet["availability"]
|
||||
pricing = packet["pricing"]
|
||||
appointment = packet["appointment"]
|
||||
installer_access = packet["installer_access"]
|
||||
payment = packet["payment"]
|
||||
speed_test = packet["speed_test"]
|
||||
|
||||
lines = [
|
||||
f"# NH Broadband Install Packet",
|
||||
"# NH Broadband Install Packet",
|
||||
"",
|
||||
f"**Packet ID:** {packet['packet_id']}",
|
||||
f"**Generated:** {packet['generated_utc']}",
|
||||
@@ -85,13 +179,44 @@ def render_markdown(packet: dict[str, Any], data: dict[str, Any]) -> str:
|
||||
f"- {addr['address']}",
|
||||
f"- {addr['city']}, {addr['state']} {addr['zip']}",
|
||||
"",
|
||||
f"## Desired Plan",
|
||||
"## Availability",
|
||||
"",
|
||||
f"{packet['desired_plan']}",
|
||||
f"- **Status:** {availability['status']}",
|
||||
f"- **Checked at:** {availability['checked_at'] or 'pending'}",
|
||||
f"- **Exact address confirmed:** {_bool_label(availability['exact_address_confirmed'])}",
|
||||
f"- **Notes:** {availability['notes'] or 'pending live lookup'}",
|
||||
"",
|
||||
"## Pricing + Plan Recommendation",
|
||||
"",
|
||||
f"- **Recommended plan:** {pricing['recommended_plan']}",
|
||||
f"- **Monthly cost:** {_money(pricing['monthly_cost_usd'])}",
|
||||
f"- **Install fee:** {_money(pricing['install_fee_usd'])}",
|
||||
f"- **Notes:** {pricing['notes'] or 'confirm on scheduling call'}",
|
||||
"",
|
||||
"## Installation Appointment",
|
||||
"",
|
||||
f"- **Scheduled:** {_bool_label(appointment['scheduled'])}",
|
||||
f"- **Date:** {appointment['date'] or 'pending'}",
|
||||
f"- **Window:** {appointment['window'] or 'pending'}",
|
||||
f"- **Confirmation #: {appointment['confirmation_number'] or 'pending'}**",
|
||||
"",
|
||||
"## Installer Access Notes",
|
||||
"",
|
||||
f"- **Installer can reach cabin:** {_bool_label(installer_access['installer_can_reach_cabin'])}",
|
||||
f"- **Driveway note:** {installer_access['driveway_note'] or 'pending'}",
|
||||
f"- **Site contact:** {installer_access['site_contact'] or contact['phone']}",
|
||||
"",
|
||||
"## Payment",
|
||||
"",
|
||||
f"- **Method:** {payment['method'] or 'pending'}",
|
||||
f"- **First month due:** {_money(payment['first_month_due_usd'])}",
|
||||
f"- **Install fee due:** {_money(payment['install_fee_due_usd'])}",
|
||||
f"- **Notes:** {payment['notes'] or 'confirm on scheduling call'}",
|
||||
"",
|
||||
"## Call Log",
|
||||
"",
|
||||
]
|
||||
|
||||
if packet["call_log"]:
|
||||
for entry in packet["call_log"]:
|
||||
ts = entry.get("timestamp", "n/a")
|
||||
@@ -112,6 +237,17 @@ def render_markdown(packet: dict[str, Any], data: dict[str, Any]) -> str:
|
||||
mark = "x" if item.get("done") else " "
|
||||
lines.append(f"- [{mark}] {item['item']}")
|
||||
|
||||
if speed_test.get("tested_at") or speed_test.get("download_mbps") or speed_test.get("upload_mbps"):
|
||||
lines.extend([
|
||||
"",
|
||||
"## Post-install Speed Test",
|
||||
"",
|
||||
f"- **Tested at:** {speed_test['tested_at'] or 'pending'}",
|
||||
f"- **Download:** {speed_test['download_mbps'] or 'pending'} Mbps",
|
||||
f"- **Upload:** {speed_test['upload_mbps'] or 'pending'} Mbps",
|
||||
f"- **Provider:** {speed_test['provider'] or 'pending'}",
|
||||
])
|
||||
|
||||
lines.append("")
|
||||
return "\n".join(lines)
|
||||
|
||||
|
||||
@@ -32,11 +32,45 @@ def test_load_and_build_packet() -> None:
|
||||
assert packet["contact"]["name"] == "Timmy Operator"
|
||||
assert packet["service_address"]["city"] == "Concord"
|
||||
assert packet["service_address"]["state"] == "NH"
|
||||
assert packet["status"] == "pending_scheduling_call"
|
||||
assert packet["availability"]["status"] == "available"
|
||||
assert packet["appointment"]["scheduled"] is True
|
||||
assert packet["pricing"]["monthly_cost_usd"] == 79.95
|
||||
assert packet["installer_access"]["installer_can_reach_cabin"] is True
|
||||
assert packet["payment"]["method"] == "credit_card"
|
||||
assert packet["status"] == "scheduled_install"
|
||||
assert len(packet["checklist"]) == 8
|
||||
assert packet["checklist"][0]["done"] is False
|
||||
|
||||
|
||||
def test_build_packet_marks_blocked_when_availability_fails() -> None:
|
||||
data = load_request("docs/nh-broadband-install-request.example.yaml")
|
||||
data["availability"] = {
|
||||
"status": "unavailable",
|
||||
"checked_at": "2026-04-17T16:00:00Z",
|
||||
"notes": "Address lookup returned no fiber service.",
|
||||
}
|
||||
data["appointment"] = {}
|
||||
data["speed_test"] = {}
|
||||
|
||||
packet = build_packet(data)
|
||||
|
||||
assert packet["status"] == "blocked_unavailable"
|
||||
|
||||
|
||||
def test_build_packet_marks_post_install_verified_when_speed_test_present() -> None:
|
||||
data = load_request("docs/nh-broadband-install-request.example.yaml")
|
||||
data["speed_test"] = {
|
||||
"tested_at": "2026-05-01T18:30:00Z",
|
||||
"download_mbps": 942.6,
|
||||
"upload_mbps": 881.4,
|
||||
"provider": "fast.com",
|
||||
}
|
||||
|
||||
packet = build_packet(data)
|
||||
|
||||
assert packet["status"] == "post_install_verified"
|
||||
|
||||
|
||||
def test_validate_rejects_missing_contact_name() -> None:
|
||||
data = {
|
||||
"contact": {"name": "", "phone": "555"},
|
||||
@@ -86,6 +120,11 @@ def test_render_markdown_contains_key_sections() -> None:
|
||||
assert "# NH Broadband Install Packet" in md
|
||||
assert "## Contact" in md
|
||||
assert "## Service Address" in md
|
||||
assert "## Availability" in md
|
||||
assert "## Pricing + Plan Recommendation" in md
|
||||
assert "## Installation Appointment" in md
|
||||
assert "## Installer Access Notes" in md
|
||||
assert "## Payment" in md
|
||||
assert "## Call Log" in md
|
||||
assert "## Appointment Checklist" in md
|
||||
assert "Concord" in md
|
||||
@@ -97,6 +136,8 @@ def test_render_markdown_shows_checklist_items() -> None:
|
||||
packet = build_packet(data)
|
||||
md = render_markdown(packet, data)
|
||||
assert "- [ ] Confirm exact-address availability" in md
|
||||
assert "Installer can reach cabin" in md
|
||||
assert "- **Confirmation #: NHB-2026-0417**" in md
|
||||
|
||||
|
||||
def test_example_yaml_is_valid() -> None:
|
||||
|
||||
Reference in New Issue
Block a user